USGARAGEDOOROPENERS.COM  Chamberlain Garage Door Remote Controls and Door Opener Keypads    

Chamberlain Garage Door Opener Parts and LiftMaster Garage Door Openers

HOME

REMOTES

PARTS

KEYPADS

CONTACT US

ABOUT US

Garage Door Opener Remote Controls and Gate Operator Parts

Phone Orders 480-247-2094

1st Garage Door Openers, Inc.
 BBB Business Review
REMOTES
REPAIR PARTS
RECEIVERS
KEYLESS ENTRY
SAFETY SENSORS
WALL CONTROLS 
LOGIC BOARDS
BACKUP BATTERIES
SURGE SUPPRESSORS
LIFTMASTER MOTOR HEADS
ACCESSORIES
LUBRICANT
DRIVEWAY ALERT
LASER PARKING
ALMOST UNIVERSAL REMOTE
HOME ACCESSORIES
SHIPPING& RETURNS
WARRANTY INFORMATION
CANCELLATION POLICY
ABOUT US
CUSTOMER
ASSISTANCE
CODING INSTRUCTIONS
FAX OR CHECK ORDERING
SITE INDEX
All Online Ordering
Is Safe and Secure

Same or Next Day Shipping

Shipping

LiftMaster Garage Door Openers 378LM Wireless Panel Coding Instructions

 

LIFTMASTER PROFESSIONAL

 

Models 378LM and 378LMC Wireless Control Panel

 

Only for use with 315MHz Security+ garage door openers and universal receivers that have a purple “learn” button.

 

To Program The Large Push Button or Auxiliary Button To A Garage Door Opener

 

1.       Press and release the “learn” button on the motor unit. The learn indicator light will glow steadily for 20 seconds.

2.       Within 30 seconds, press and hold the large push button or auxiliary button on the wireless control panel.

3.       Release the button when the motor unit light blinks. It has learned the code. If the light bulbs are not installed, two clicks will be heard.

 

To Erase All Codes From Motor Unit Memory

 

To deactivate any unwanted remote, first erase all codes:

 

Press and hold the “learn” button on motor unit until the learn indicator light goes out (approximately 6 seconds). All previous codes are now erased. Reprogram each remote or keyless entry you wish to use.

 

To Control the Opener Lights

 

NOTE:  Feature not available with universal receiver.

With 315MHz Security+ wireless control panel, the Light button can be programmed to operate the opener lights without opening the door. A wired multi-fuction control panel is required to program the Light button on the wireless control panel.

1.       With the door closed, press and hold the Light button on the wireless control panel.

2.       Press and hold the Light button on the multi-function control panel.

3.       Press and hold the Lock button on the multi-function control panel.

4.       After the opener lights flash, release all buttons.

Test by pressing the Light button on the wireless control panel.

The opener lights should turn on or off but the door should not move.

 

***************WARNING***************

To prevent possible SERIOUS INJURY or DEATH from a moving gate or garage door:

·         Install door control within sight or garage door, out of reach of children at a minimum height of 5’ (1.5m), and away from all moving parts of door.

·         NEVER permit children to operate or play with door control push buttons or remote control transmitters.

·         Activate door ONLY when it can be seen clearly, is properly adjusted and there are no obstructions to door travel.

·         ALWAYS keep garage door in sight until completely closed. NEVER permit anyone to cross the path of closing garage door.

*******************************************

 

Installation

 

NOTE:  Locate the door control within sight of the door at a minimum height of 5’ (1.5m) where small children cannot reach and away from all moving parts of the door and door hardware.

 

Remove the push button cover by gently prying off the top edge with a screwdriver. Fasten with 6Abx1-1/4” self-tapping screws as follows:

·         Drill pilot holes and install bottom screw, allowing 1/8” (3mm) to protrude above the wall surface.

·         Position bottom of door control on screw head and slide down to secure. Adjust screw for snug fit.

·         Install top screw. DO NOT overtighten, you may damage the plastic housing.

 

The Wireless Control Panel Batteries

***************WARNING***************

To prevent possible SERIOUS INJURY or DEATH:

·         NEVER allow small children near batteries.

·         If battery is swallowed, immediately notify doctor.

*******************************************

 

The Lithium batteries should produce power for up to 5 years. To replace the batteries, remove the two screws and the logic board from the plastic housing. Insert new batteries positive side up (+).

Dispose of old batteries properly.

Home | Remotes | Keyless Entry | Chain Motor Repair Parts | Belt Motor Repair Parts | Screw Motor Repair Parts | Chain Rail Assembly Parts | Belt Rail Assembly Parts | Screw Rail Assembly Parts | Wall Controls | Accessories | Lubricants | Surge Suppressors | Safety Sensors | Logic Boards | Receivers | Coding Instructions | Customer Assistance | Remote Compatibility | Board Compatibility | Fax or Check Ordering | Shipping & Returns | Compatible Brand Names | Site IndexAbout Us

Sears Craftsman, Chamberlain, LiftMaster, Master Mechanics, Wayne Dalton and all other Brands of Garage Door openers are registered trade names of the respective entities and are only used for reference

      

  

1st Garage Door Openers, Inc an Independent Garage Door Opener Dealer
Copyright © 2010 - 2017  All Rights Reserved. No part of this site can be reproduced in any form or by any means, photocopying, electronic, mechanical, or otherwise, without the prior written permission of  1st Garage Door Openers Inc., Mesa, AZ 85203