USGARAGEDOOROPENERS.COM  Chamberlain Garage Door Remote Controls and Door Opener Keypads    

Chamberlain Garage Door Opener Parts and LiftMaster Garage Door Openers

HOME

REMOTES

PARTS

KEYPADS

CONTACT US

ABOUT US

Garage Door Opener Remote Controls and Gate Operator Parts

Phone Orders 480-247-2094

1st Garage Door Openers, Inc.
 BBB Business Review
REMOTES
REPAIR PARTS
RECEIVERS
KEYLESS ENTRY
SAFETY SENSORS
WALL CONTROLS 
LOGIC BOARDS
BACKUP BATTERIES
SURGE SUPPRESSORS
LIFTMASTER MOTOR HEADS
ACCESSORIES
LUBRICANT
DRIVEWAY ALERT
LASER PARKING
ALMOST UNIVERSAL REMOTE
HOME ACCESSORIES
SHIPPING& RETURNS
WARRANTY INFORMATION
CANCELLATION POLICY
ABOUT US
CUSTOMER
ASSISTANCE
CODING INSTRUCTIONS
FAX OR CHECK ORDERING
SITE INDEX
All Online Ordering
Is Safe and Secure

Same or Next Day Shipping

Shipping

Garage Door Opener Parts

Liftmaster

PROFESSIONAL

Model 64LM Mini Multi-Function Transmitter

The multi-function mini transmitter has three buttons. The large top button is recommended for use with a garage door opener and/or light control product. The other push buttons can be used to operate another garage door opener and/or light control product. Instructions for programming light controls are included with those accessories.

To match the code switches in the new and original transmitters:

Locate the code switches in the multi-function mini transmitter by turning the transmitter over and removing the case screw and removing the back of the case. Be careful to avoid moving the circuit board components.

Place the new transmitter and the original transmitter side by side, and set the switches in both transmitters to matching positions (+,0,-). Use a pen or screwdriver to slide the code switches.

NOTE: Code switch #1 in the multi-function mini transmitter is dormant, when used with a single-function transmitter. Set code switch #1, in the single function transmitter, to match the push button selected on the multi-function mini transmitter.

*************   WARNING   *************

            Moving Door can cause serious injury or death.

·         DO NOT install transmitter unless the door operator’s safety reverse works as required by the door operator’s manual.

·         Wall control must be mounted in sight of door, at least 5 feet above floor and clear of moving door parts.

·         Keep people clear of opening while door is moving.

·         DO NOT allow children to play with the transmitter or door operator.

If safety reverse does not work properly:

·         Close door then disconnect operator using the manual release handle.

·         DO NOT use transmitter or door operator.

·         Refer to Door and Door Operators Owner’s Manuals before attempting any repairs.

_________________________________________________

            Electrical Shock can cause serious injury or death.

·         Power cord must be unplugged before attaching any wires,

·         Be sure wire ends do not touch each other or other terminals.

If you have questions or if you need a manual, contact the distributor or manufacturer of the operator.

***************************************************************************************************************

Programming the opener

If your unit has a “Learn” button:

1.   Press and release the “learn “ button. This can be found where you see the antenna wire hanging from the motor head (you may have to take the lens cover off). If antenna wire is not hanging from motor head then you have an external receiver which is a black box approx. 6" x 2" mounted somewhere in the garage with a antenna wire hanging from it (pop off cover to find Learn Code Button). The learn indicator light will glow steadily for 30 seconds.

2.    Within the 30 second window, press and hold the button on the hand-held remote.

3.     The unit will either activate or the opener light bulb will blink signifying it has learned the code.

If your unit has code switches:

    1.    Using a step ladder climb up to the back of your motor unit. Check the code switch          settings on the back of the motor unit. Your code block with dip switches can be found where you see the antenna wire hanging from the motor head (you may have to take the lens cover off). If antenna wire is not hanging from motor head then you have an external receiver which is a black box approx. 6" x 2" mounted somewhere in the garage with a antenna wire hanging from it (pop off cover to find code block with dip switches).

2.   Use a pen or screw driver to set the code switches on the back of the transmitter to match the code switches on the back of the motor unit.

3.   Once the code switches have been set push the transmitter button to activate your unit.

Replacing the transmitter battery

The 12Volt battery should provide power for up to 1 year. To replace the battery remove the case screw and the cover.

Dispose of old batteries properly.

Locate the battery by sliding the battery compartment cover.

Dispose of old batteries properly.

 

 

Home | Remotes | Keyless Entry | Chain Motor Repair Parts | Belt Motor Repair Parts | Screw Motor Repair Parts | Chain Rail Assembly Parts | Belt Rail Assembly Parts | Screw Rail Assembly Parts | Wall Controls | Accessories | Lubricants | Surge Suppressors | Safety Sensors | Logic Boards | Receivers | Coding Instructions | Customer Assistance | Remote Compatibility | Board Compatibility | Fax or Check Ordering | Shipping & Returns | Compatible Brand Names | Site IndexAbout Us

Sears Craftsman, Chamberlain, LiftMaster, Master Mechanics, Wayne Dalton and all other Brands of Garage Door openers are registered trade names of the respective entities and are only used for reference

      

  

1st Garage Door Openers, Inc an Independent Garage Door Opener Dealer
Copyright © 2010 - 2017  All Rights Reserved. No part of this site can be reproduced in any form or by any means, photocopying, electronic, mechanical, or otherwise, without the prior written permission of  1st Garage Door Openers Inc., Mesa, AZ 85203