USGARAGEDOOROPENERS.COM  Chamberlain Garage Door Remote Controls and Door Opener Keypads    

Chamberlain Garage Door Opener Parts and LiftMaster Garage Door Openers

HOME

REMOTES

PARTS

KEYPADS

CONTACT US

ABOUT US

Garage Door Opener Remote Controls and Gate Operator Parts

Phone Orders 480-247-2094

1st Garage Door Openers, Inc.
 BBB Business Review
REMOTES
REPAIR PARTS
RECEIVERS
KEYLESS ENTRY
SAFETY SENSORS
WALL CONTROLS 
LOGIC BOARDS
BACKUP BATTERIES
SURGE SUPPRESSORS
LIFTMASTER MOTOR HEADS
ACCESSORIES
LUBRICANT
DRIVEWAY ALERT
LASER PARKING
ALMOST UNIVERSAL REMOTE
HOME ACCESSORIES
SHIPPING& RETURNS
WARRANTY INFORMATION
CANCELLATION POLICY
ABOUT US
CUSTOMER
ASSISTANCE
CODING INSTRUCTIONS
FAX OR CHECK ORDERING
SITE INDEX
All Online Ordering
Is Safe and Secure

Same or Next Day Shipping

Shipping

Garage Door Opener and Repair Parts

Liftmaster

PROFESSIONAL

WIRELESS KEYLESS ENTRY – MODEL SERIES 740 AND 66

FEATURES OF THE KEYPAD TRANSMITTER

Personalized Code: Up to 10,000 possible combinations. Codes can easily be changes if desired.

Operation: Opener activates when 4-code digits and ENTER button are pressed.

The Keypad Transmitter will open and close the door even if the Door control Lock Switch feature is ON.

If wrong numbers are accidentally pressed, correction can be made immediately. The Enter key will transmit only the last four digits.

The keypad will blink for 15 seconds after the code is transmitted. During that time you can STOP or REVERSE door travel just by pressing the ENTER key.

The keypad transmitter can be used with garage door opener receivers having a yellow, gray, white or green “learn” button.

Setting the Code:

1.       Press and release the “learn” button on motor unit.  This can be found where you see the antenna wire hanging from the motor head (you may have to take the lens cover off). If antenna wire is not hanging from motor head then you have an external receiver which is a black box approx. 6" x 2" mounted somewhere in the garage with a antenna wire hanging from it (pop off cover to find Learn Code Button). The learn indicator light will glow steadily for 30 seconds.

2.       Within 30 seconds, enter a four-digit personal identification number (PIN) of your choice on the keypad. Then press and hold the ENTER button.

3.       Release the button when the motor unit lights blink. It has learned the code. If light bulbs are not installed, two clicks will be heard.

*************   WARNING   *************

            Moving Door can cause serious injury or death.

·         DO NOT install transmitter unless the door operator’s safety reverse works as required by the door operator’s manual.

·         Wall control must be mounted in sight of door, at least 5 feet above floor and clear of moving door parts.

·         Keep people clear of opening while door is moving.

·         DO NOT allow children to play with the transmitter or door operator.

If safety reverse does not work properly:

·         Close door then disconnect operator using the manual release handle.

·         DO NOT use transmitter or door operator.

·         Refer to Door and Door Operators Owner’s Manuals before attempting any repairs.

            Electrical Shock can cause serious injury or death.

·         Power cord must be unplugged before attaching any wires,

·         Be sure wire ends do not touch each other or other terminals.

If you have questions or if you need a manual, contact the distributor or manufacturer of the operator.

***************************************************************************************************************

The Keyless Entry Battery:

The 12-volt battery should produce power for at least one year. Replace when the keypad illumination becomes dim.

Dispose of old batteries properly.

Installation:

Open the keypad cover and remove the battery compartment screw. Take out the battery. Note the battery polarity as marked on compartment.

Follow the installation instructions described below.

1.       Center the keypad at eye level against the selected location on garage exterior as shown.

NOTE: For a one-piece door on a brick, stone or aluminum sided garage, use an optional location as the door swings up and out.

2.       Hold keypad firmly with cover half open so both the top and bottom-mounting holes are visible. Use a punch to mark each hole. Drill two 1/8” pilot holes. Fasten securely with screws provided.

3.       Insert the plug provided into the top hole to cover the fastening screw. Return the battery, being sure to observe polarity. Re-fasten compartment cover.

 

 

 

Home | Remotes | Keyless Entry | Chain Motor Repair Parts | Belt Motor Repair Parts | Screw Motor Repair Parts | Chain Rail Assembly Parts | Belt Rail Assembly Parts | Screw Rail Assembly Parts | Wall Controls | Accessories | Lubricants | Surge Suppressors | Safety Sensors | Logic Boards | Receivers | Coding Instructions | Customer Assistance | Remote Compatibility | Board Compatibility | Fax or Check Ordering | Shipping & Returns | Compatible Brand Names | Site IndexAbout Us

Sears Craftsman, Chamberlain, LiftMaster, Master Mechanics, Wayne Dalton and all other Brands of Garage Door openers are registered trade names of the respective entities and are only used for reference

      

  

1st Garage Door Openers, Inc an Independent Garage Door Opener Dealer
Copyright © 2010 - 2017  All Rights Reserved. No part of this site can be reproduced in any form or by any means, photocopying, electronic, mechanical, or otherwise, without the prior written permission of  1st Garage Door Openers Inc., Mesa, AZ 85203