USGARAGEDOOROPENERS.COM  Chamberlain Garage Door Remote Controls and Door Opener Keypads    

Chamberlain Garage Door Opener Parts and LiftMaster Garage Door Openers

HOME

REMOTES

PARTS

KEYPADS

CONTACT US

ABOUT US

Garage Door Opener Remote Controls and Gate Operator Parts

Phone Orders 480-247-2094

1st Garage Door Openers, Inc.
 BBB Business Review
REMOTES
REPAIR PARTS
RECEIVERS
KEYLESS ENTRY
SAFETY SENSORS
WALL CONTROLS 
LOGIC BOARDS
BACKUP BATTERIES
SURGE SUPPRESSORS
LIFTMASTER MOTOR HEADS
ACCESSORIES
LUBRICANT
DRIVEWAY ALERT
LASER PARKING
ALMOST UNIVERSAL REMOTE
HOME ACCESSORIES
SHIPPING& RETURNS
WARRANTY INFORMATION
CANCELLATION POLICY
ABOUT US
CUSTOMER
ASSISTANCE
CODING INSTRUCTIONS
FAX OR CHECK ORDERING
SITE INDEX
All Online Ordering
Is Safe and Secure

Same or Next Day Shipping

Shipping

Garage Door Opener Parts

Liftmaster

PROFESSIONAL

Model 976LM, 977LM, 976LMC, 940CB Security+ Wireless Keyless Entry

Features:

For use with any SECURITY+ garage door openers having an orange “learn” button.

Personalized password: Up to 10,000 possible combinations. Password can be easily changes if desired.

Temporary Password: Can be added for visitors or service persons. This temporary password can be limited to a programmable number of hours or a programmable number of entries.

Rolling Code: While your password remains constant until you change it, the code between the Keyless Entry and the receiver changes with each use, randomly accessing over 100 billion new codes.

Operation: Opener activates when 4-digit password and Enter button is pressed.

If wrong numbers are accidentally pressed, correction can be made immediately. The Enter button will transmit only the last four digits.

The Keypad will blink for 15 seconds after the password is transmitted. During that time the Enter button can be used to stop or reverse the door travel.

SETTING THE PERSONAL ENTRY PASSWORD:

We recommend that you program your password now, before you install the Keyless Entry. Then you can test the reception at the mounting location before you proceed further.

USING THE MULTI-FUNCTION DOOR CONTROL:

  1. Enter a four-digit personal identification number (PIN) of your choice on the keypad. Then press and hold ENTER.
  2. While holding the ENTER button, press and hold the LIGHT button on the Multi-Function Door Control.
  3. Continue holding the ENTER AND light BUTTONS WHILE YOU PRESS THE PUSH BAR ON THE Multi-Function Door Control (all three buttons are held).
  4. Release buttons when the motor unit lights blink. It has learned the code. If light bulbs are not installed, two clicks will be heard.

*************   WARNING   *************

            Moving Door can cause serious injury or death.

·         DO NOT install transmitter unless the door operator’s safety reverse works as required by the door operator’s manual.

·         Wall control must be mounted in sight of door, at least 5 feet above floor and clear of moving door parts.

·         Keep people clear of opening while door is moving.

·         DO NOT allow children to play with the transmitter or door operator.

If safety reverse does not work properly:

·         Close door then disconnect operator using the manual release handle.

·         DO NOT use transmitter or door operator.

·         Refer to Door and Door Operators Owner’s Manuals before attempting any repairs.

_________________________________________________

            Electrical Shock can cause serious injury or death.

·         Power cord must be unplugged before attaching any wires,

·         Be sure wire ends do not touch each other or other terminals.

If you have questions or if you need a manual, contact the distributor or manufacturer of the operator.

***************************************************************************************************************

USING THE “LEARN” BUTTON

1.       Press and release the “learn” button on motor unit.   This can be found where you see the antenna wire hanging from the motor head (you may have to take the lens cover off). If antenna wire is not hanging from motor head then you have an external receiver which is a black box approx. 6" x 2" mounted somewhere in the garage with a antenna wire hanging from it (pop off cover to find Learn Code Button). The learn indicator light will glow steadily for 30 seconds.

2.       Within 30 seconds, enter a four-digit personal identification number (PIN) of your choice on the keypad. Then press and hold the ENTER button.

3.       Release the button when the motor unit lights blink. It has learned the code. If light bulbs are not installed, two clicks will be heard.

INSTALLATION:

Chooses a convenient location for installation. It should be at eye level. Reachable by the shortest person who will use it, and within sight of the door.

For a one-piece door, install on exterior front wall to avoid injury as the door swings up and out.

Test the reception of the Keyless Entry by operating your opener from the selected location. Change the location if necessary.

Remove the battery compartment cover to access the bottom-mounting hole:

·         Insert a small Phillips screwdriver into the small hole at the bottom of the cover and gently pull outward to loosen.

·         Slide cover down to remove.

Center the keypad at eye level against the selected location. Mark 4-1/4 “ up the centerline from the bottom and drill a 1/8” pilot hole. Install top mounting screw, allowing 1/8” to protrude above the surface. Position keypad on screw head and adjust for snug fit.

With cover open so bottom-mounting hole is visible, use a punch to mark hole. Remove keypad and drill 1/8” pilot hole. Replace keypad and complete installation with bottom screw, using care to avoid cracking plastic housing. Do not over tighten.

To replace the battery cover, insert the lip at the top and snap in place.

THE KEYLESS ENTRY BATTERY

The 9-volt battery should produce power for at least one year. Replace when the keypad illumination becomes dim. Dispose of old batteries properly.

TO CHANGE AN EXISTING, KNOWN PIN:

If the existing PIN is known, one person may change it without using a ladder.

  1. Press the four buttons for the present PIN, then press and hold the # button.

The opener light will blink twice. Release the # button.

  1. Press the new 4-digit PIN you have chosen, and then press ENTER.

The motor unit lights will blink once when the PIN has been learned.

Test by pressing the new PIN, then press ENTER. The door should move.

TO SET A TEMPORARY PIN:

You may authorize access by visitors or service people with a temporary 4-digit PIN. After a programmed number of hours or number of accesses, this temporary PIN expires and will no longer open the door. It can be used to close the door even after it has expired. To set a temporary PIN:

1)       Press the four buttons for your personal entry PIN (not the last temporary PIN), then press and hold the *button.

The opener light will blink three times. Release the button.

2)        Press the temporary 4-digit PIN you have chosen, and then press ENTER.

The opener light will blink four times.

3)       To set the number of hours this temporary PIN will work, press the number of hours (up to 255), then press *.

                                                                   OR

  1. To set the number of times this temporary PIN will work, press the number of hours (up

To 255), then press #.

The opener light will blink once when the temporary PIN has been learned.

Test by pressing the four buttons for the temporary PIN, then press ENTER. The door should move. If the temporary PIN was set to a certain number of openings, remember that the test has used up one opening. To clear the temporary password, repeat steps 1-3, setting the number of hours or times to 0 in step 3.

SPECIAL NOTE: The temporary password can ONLY be programmed to keypads working on a Chamberlain or Lift-Master Garage Door Opener. It WILL NOT work on keypads programmed to an external receiver.

The temporary password will continue to CLOSE the door even after the time has expired. To eliminate this, program a new temporary password into the keypad.

 

 

Home | Remotes | Keyless Entry | Chain Motor Repair Parts | Belt Motor Repair Parts | Screw Motor Repair Parts | Chain Rail Assembly Parts | Belt Rail Assembly Parts | Screw Rail Assembly Parts | Wall Controls | Accessories | Lubricants | Surge Suppressors | Safety Sensors | Logic Boards | Receivers | Coding Instructions | Customer Assistance | Remote Compatibility | Board Compatibility | Fax or Check Ordering | Shipping & Returns | Compatible Brand Names | Site IndexAbout Us

Sears Craftsman, Chamberlain, LiftMaster, Master Mechanics, Wayne Dalton and all other Brands of Garage Door openers are registered trade names of the respective entities and are only used for reference

      

  

1st Garage Door Openers, Inc an Independent Garage Door Opener Dealer
Copyright © 2010 - 2017  All Rights Reserved. No part of this site can be reproduced in any form or by any means, photocopying, electronic, mechanical, or otherwise, without the prior written permission of  1st Garage Door Openers Inc., Mesa, AZ 85203